Beacon 110 Single Channel Wall Mount Controller
The Beacon 110 is a powerful, low cost fixed system controller for one point of gas detection. It is microprocessor controlled, versatile, simple to install and operate, and priced to be the industry's best value single gas detection controller. It is capable of accepting RKI sensors directly for LEL level combustibles, Oxygen, Hydrogen Sulfide, or Carbon Monoxide. The Beacon 110 can also accept any 4-20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly at the Beacon 110 housing, or can be wired remote from the controller.
The 10 amp rated relays are strong enough to directly power external alarms and horns. The digital display has backlighting and simultaneous readout of the gas type and concentration.
The Beacon 110 is also housed in a NEMA 4X rated case for a weather tight seal. This case design complies with lock out / tag out standards and can be fully secured. An external reset switch allows the alarm to be silenced from outside of the controller housing. The Beacon 110 ships complete with a wall mounting kit for easy installation.
Features:- Low cost versatile solution
- Compact, weatherproof, NEMA 4X enclosure
- 115/220 VAC or 24 VDC operation
- Long life sensors (2+ years typical)
- Accepts RKI LEL/O2/H2S/CO direct connect sensors
- Accepts any 4-20 mA transmitter
- Audible alarm with reset button
- Two programmable alarm levels
- Built-in trouble alarm with relay
- Relay rating 10 amps, form C
- Provides 4-20 mA output
Beacon 110 Single Channel Wall Mount Controller
PHYSICAL
|
| Dimensions | Height: 8.5" (216 mm)
Width: 7.0" (178 mm)
Depth: 4.3" (109 mm) |
| Enclosure | Wall mounting gray polycarbonate with hinged cover |
| Conduit Connection | 3/4" NPT conduit hubs, 2 provided
1 for sensor wiring
1 for power & relay wiring |
| Wiring Termination | Screw type terminal block 14 gauge max |
| Power | Universal 115 VAC & 220 VAC, or 24 VDC nominal,
battery backup option available |
| Controls | 3 internal push buttons for setup, programming,
& calibration. 1 external push button for alarm reset |
| ENVIRONMENTAL |
| Operating Temp | -4°F to 122°F (-20°C to 50°C) |
| Storage Temp | -4°F to 158°F (-20°C to 70°C) |
| Relative Humidity | 0 - 100% RH |
| Enclosure Rating | NEMA -4X enclosure, waterproof, chemical, &
weather resistant |
| INPUTS | |
| Direct Wired Sensors | LEL
Oxygen
Carbon Monoxide
Hydrogen Sulfide
Remote amp not required for less than 500 ft. |
| 4-20 mA Sensors | Accepts any 4-20 mA transmitter (24 VDC, 2
or 3 wire). A wide variety of RKI / Riken sensors
are available with 4-20 mA signals. Wiring distances
up to 5,000 ft. |
| Sampling Methods | Diffusion & sample draw heads available. |
| OUTPUTS | |
| Relays | 3 relays - 10 amp rating (at 115 VAC), SPDT
isolated contacts. 2 relays for gas alarms and 1
trouble relay.
Relays fully programmable for:
-increasing or decreasing alarm
-latching or self reset
-normally energized or normally de-energized
-time delay for alarm on / off |
| 4-20 mA | Signal output, 4-20 mA (maximum load impedance
500 ohms), per channel |
| 24 VDC | 24 VDC (400 mA max) output provided to operate
sample drawing adapters or other accessories |
| Display | 2 x 8 Alphanumeric display with backlighting |
| Audible | Built-in audible alarm, 94 dB, mounted on enclosure
Coded output: pulsing = gas alarm, steady = fail |
| Visual | 3 LED's on the front cover for alarm status
indication and malfunction |
| WARRANTY | 1 Year Materials and Workmanship |
Beacon 110 Single Channel Wall Mount Controller
There are no reviews yet.